Home

Stainless Steel body to help prevent rusting

complete with pocket clip

Spring tension & oval push-button Lock-Nut firmly positions and holds Soapstone

Includes 1 piece 5" Soapstone 

Free NEXT DAY Delivery (Orders over £7.50 + VAT) 

Replacement Dial-Set-Level for all Curve-O-Mark products fitted with a DSL.

Made of durable lightweight cast aluminium 

Reads in 2.5-degree increments

Protractor covers 180-degrees thru two 90-degree quadrants

Suppled complete with washers and screw. 

Folding sturdy friction joints to maintain rigidity and accuracy, made from lightweight, rustproof aluminum for lastability. A soapstone crayon is already installed in each radius marker. The scribe holder will accept round square or flat soapstone crayon, pencil, or steel point scribe.

Up to 8" radius

Designed for use with the Curv-O-Mark Standard and Jumbo Contour Markers, the Adaptor simplifies handling and increases layout capacity. The Adaptor permits use of all four sides the Contour Marker and permits marking on small diameter pipe, over nipples, old welds or on wrapped pipe. The Adaptor can also provide layouts with compound angles using a single setting or any degree of take-off on elbows and turns up to 90 degrees. Use with Curv-O-Mark Contour Marker Jumbo (COM0004)

A hardened steel pin for use with the Curv-O-Mark Standard Centering Head. Suitable for marking, but should not be used as a centre punch.

FREE NEXT WORKING DAY DELIVERY (Order before 3:00pm)

Folding sturdy friction joints to maintain rigidity and accuracy, made from lightweight, rustproof aluminium for long last-ability. A soapstone crayon is already installed in each radius marker. The scribe holder will accept round square or flat soapstone crayon, pencil, or steel point scribe.

Up to 20" radius

FREE NEXT WORKING DAY DELIVERY (Order before 3:00pm)

2235Curv-O-Mark Wrap-A-Round rulers are an easy-to-use tool for pipe fitters and welders.  Each are printed with a scale in inches, an inch chart, tangent chart, and other helpful markings to help make a straight line around pipes. Made from flexible gasket material, they have a good resistance to both heat and cold.

An economical tool for marking straight lines around pipe or for use as a straight edge.

10Curv-O-Mark Wrap-A-Round rulers are an easy-to-use tool for pipe fitters and welders.  Each are printed with a scale in inches, an inch chart, tangent chart, and other helpful markings to help make a straight line around pipes. Made from flexible gasket material, they have a good resistance to both heat and cold.

An economical tool for marking straight lines around pipe or for use as a straight edge. 

3Made with an anodized rust proof aluminium for lasting protection

Arms are precisely aligned with spring tension joints to guarantee accuracy and rigidity

Holder accommodates flat or round soapstone and pencils

Folding type design.

Fits conveniently in a shirt pocket

Trammel points are the most accurate means of drawing arcs and circles because you can lock the radius tight.

Space saving tool leaving plenty of room in your tool box by taking just the points around. You can use any standard 1/2" pipe or conduit that you can find on any job site to create the radius you need.

Made with an anodized rust proof aluminium for lasting protection.

Arms are precisely aligned with spring tension joints to guarantee accuracy and rigidity.

Holder accommodates flat or round soapstone and pencils.

Folding type design.  

Up to 40" radius.

Curv-O-Mark Wrap-A-Round rulers are an easy-to-use tool for pipe fitters and welders.  Each are printed with a scale in inches, an inch chart, tangent chart, and other helpful markings to help make a straight line around pipes. Made from flexible gasket material, they have a good resistance to both heat and cold.

An economical tool for marking straight lines around pipe or for use as a straight edge. 

Designed for use with the COM0001 Standard Contour Marker, the adapter simplifies handling and increases layout capacity. 

It permits the use of all four sides of the Contour Marker and allows marking on small diameter pipe, over nipples, old weld, or on wrapped pipe.

21Curv-O-Mark Wrap-A-Round rulers are an easy-to-use tool for pipe fitters and welders.  Each are printed with a scale in inches, an inch chart, tangent chart, and other helpful markings to help make a straight line around pipes. Made from flexible gasket material, they have a good resistance to both heat and cold.

An economical tool for marking straight lines around pipe or for use as a straight edge. 

FREE NEXT WORKING DAY DELIVERY (Order before 3:00pm)

The Curv-O-Mark 90-degree protractor has a matching locking lever to set and hold the tool at the desired angle. It is equipped with a 5/8" x 10" tapered arm to complete finding of angles or desired bends, or to determine any portions of elbows.

The tool is mounted in a 3/4" wide frame with a 3/8" x 6" cast-in rod.

It comes with a 25-pound pull magnetic base for holding the protractor frame in position.

FREE NEXT WORKING DAY DELIVERY (Order before 3:00pm)

Aids in the setting of centre lines, establishing angles and marks for butt-ins, location points inside pipes and tanks, laying out key ways, and measuring declivity. 

The standard head model is used on 1/2" diameter pipe and up. 

It features a 4 inch "Y" type head fitted with an adjustable Dial-Set-Level (DSL)

Tap with a hammer to operate the hardened cantering pin.

6Removes the difficulty of flange aligning and squaring

Notched at either end for ease in aligning on the centerline of the pipe

Includes two 25-pound pull, cast-in magnets for holder in either a flat horizontal or vertical position

Base will accept either leg of a standard or combination square

Will work on pipe diameters from 1" on up requiring only the extension on the legs of the square being used to accommodate larger diameters.

Use with Standard Flange Aligner (COM0010)

Aids in the setting of center lines, establishing angles, and marks for butt-ins, locating points inside pipes and tanks, laying out keyways and measuring declivity. 

Jumbo centering head is ideal for pipe 1" diameter and above and has an 8" Y-type head and a Dial Set Level (DSL). 

A spring loaded hardened centering pin eliminates the need for a hammer.

The Curv-O-Mark Contour Marker is a compact, timesaving tool used to lay out pipe and structural steel joints. Laterals at any angle, tees, wyes, crosses and elbows.

Any type or size of joint can be quickly and precisely laid out. No complicated mathematical formulas. No  cut and try. No material waste. 

FREE NEXT WORKING DAY DELIVERY (Order before 3:00pm)

Curv-O-Mark Pipe Flange Aligner is a self-determining flange aligning tool that allows quick and accurate measuring. 

The aligner inserts easily into the pipe and centres snugly against the pipe’s inside diameter.

A manual tool that takes the guess work out of pipe construction. 

Made of durable and lightweight aluminium

Features slotted pins with "friction fitting" knurled nuts for flanges up to 30" - 150 lbs

All models of the flange aligning tools are two-hole (make 2 holes of the flange horizontally level with the ground and vertically level the face of the flange in one step.)

Adjustable for pipes and flanges from 3 to 12 inches in diameter

Use with (COM0032)

FREE NEXT WORKING DAY DELIVERY (Order before 3:00pm)

A lightweight, easy to use tool for determining angles, the Pro-Mag Level has two cast-in 25-pound pull magnets that hold securely to any steel surface. The unit has a 360-degree adjustable Dial-Set-Level (DSL) with two 90-degree quadrants graduated in 2-1/2"-degree increments. Also cast in are tables used to convert degree-of-angle to rise-in-inches-per-foot or millimetres-per meter. A groove on the bottom edge allows the level to be used on small diameter pipe.

9” long, 2” high, 3/4” thick

The Curv-O-Mark Circle Ellips Projector creates Perfect circles, ellipses or oblong circles easily on any irregular flat or round surface.

The Projector features a protractor with sliding rods and an adjustable lever to lock in the specified layout.

A strong, 20-pound pull magnetic base holds the Projector in position during layout. A durable web strap (included) holds the unit secure on non-magnetic surfaces and can be used on either side of the vertical column.

The Projector can also be used to lay out lateral intersections of different diameter pipes, or to project circles from 1-1/2" to 18" diameter on flat surfaces intersecting at angles from 0 to 70 degrees from vertical.

FREE NEXT WORKING DAY DELIVERY (Order before 3:00pm)

A MUST-HAVE TOOL for welders! Featuring a 360-degree adjustable protractor dial bubble the level has two cast-in 25-pound magnets to securely hold the unit in place on any steel surface including the underside of a pipe or beam. This permits hands free levelling, even in the tight spots.

FREE NEXT WORKING DAY DELIVERY (Order before 3:00pm)

The Curv-O-Mark Jumbo Contour Marker is a timesaving tool used to lay out pipe and structural steel joints.

Laterals at any angle, tees, wyes, crosses, elbows - any type or size of joint can be quickly and precisely laid out. No requirement for mathematical formulas or test cuts and material waste.  

Can be used with optional Curv-O-Mark Jumbo Combination Adapter